Technical Specifications
| Material | Polyurethane decorative material |
|---|---|
| Surface | Decorative molded surface; can be painted after appropriate preparation. |
| Color | Paintable surface; final color depends on the selected paint system. |
| Density | Belirtilmemiştir. |
| Water Absorption | below 1% |
| Dimensional Stability Test | -20 °C / +70 °C |
| Fire Class | B2 (DIN 4102-1) |
| Paintable | Yes |
| Usage | Indoor + Outdoor |
| Water Resistant | Yes |
| Diameter | Ø 56 cm |
| Dimensions | 555 × 555 × 255 mm |
| Sales Unit | piece |
Details
Support
Similar Products(Pilaster Capitals)
The P5040D Pilaster Capital is a Poliüretan decorative element designed for the upper section of columns and pilasters. Measuring 56 x 56 x 26 cm, it creates a broad surface and a distinct architectural accent. It can be used as a decorative capital that completes the column shaft in classical facade arrangements, entrance compositions and interior design projects.
Rigid, closed-cell polyurethane provides low water absorption, high dimensional stability and light weight. The material density is 150-220 kg/m³. Dimensional stability has been tested between -20 °C and +70 °C, and it retains its form under normal application conditions. Water absorption is below 1%. The product is not a structural load-bearing element; it is applied over an existing supporting system as a decorative covering or architectural finishing element.
The 56 x 56 cm square plan of the P5040D creates a strong upper finish on a pilaster surface, while its 26 cm depth gives the facade or wall a clearly visible projection. Its decorative, paintable surface can be adapted to the colour scheme of the space. The factory primer prepares the surface for water-based or synthetic paint; applying an additional primer is optional. Paint manufacturers may not provide a warranty for surfaces painted without their own primer. Polure does not warrant the paint systems used and accepts no responsibility for them.
As a pilaster capital, the P5040D can finish the vertical pilasters around villa entrance doors, strengthen column compositions in hotel lobbies, or create a classical architectural frame at restaurant and office entrances. It can also be used as the upper element of a decorative column arrangement in living rooms, entrance halls and stair halls. Exterior use is possible, but unpainted polyurethane may yellow under UV exposure, so a UV-resistant exterior paint is required.
Before installation, the surface must be clean, dry and sound. Required cuts are made with a 45° mitre, and the pieces are secured with polyurethane (PU) mounting adhesive. Mechanical fixing with screws and suitable fasteners is mandatory; additional mechanical support should be assessed for wide applications or installations subject to connection loads. Joints and screw points are filled with filler, smoothed with 180-220 grit sandpaper, then primed and painted with two coats. Silicone adhesive must not be used.
Compared with plaster and solid wood, rigid PU is a lighter decorative material that offers greater resistance to moisture and decay and is easier to cut and repair. It provides a harder, more detailed surface than EPS foam. The P5040D is suitable for projects seeking to complete a classical pilaster design with a dimensionally defined, paintable element that can be adapted to interior and exterior conditions.
- The P5040D Pilaster Capital is used as a decorative element that completes the upper section of a column shaft
- It creates a classical vertical composition at the ends of pilasters around villa entrance doors, in spacious entrance halls and in stair halls
- In living rooms, it can complete pilaster designs around fireplaces, passage openings or niches
- In hotel lobbies, restaurant entrances and prestigious office reception areas, it can be applied over existing column or pilaster surfaces as a decorative covering
- Outdoors, it can be used at the entrances of villas, residential buildings and commercial properties, at the upper end of vertical architectural arrangements around doors and windows
- The 56 x 56 cm square plan is best suited to wider pilaster surfaces, while the 26 cm depth creates a distinct shadow effect on a flat facade
- The product is not structural and does not replace the existing concrete, steel or masonry structure
- UV-resistant paint must be applied for exterior use
- The installation surface must be clean, dry, sound and free of dust
- The position of the piece is measured and marked, and the required joint and corner cuts are prepared with a 45° mitre
- The P5040D is bonded to the surface only with polyurethane (PU) mounting adhesive; silicone adhesive must not be used
- Mechanical fixing with screws is mandatory because the product has its own weight and connection loads
- Screws and wall plugs must be selected according to the substrate
- Joints and screw heads are covered with suitable filler
- Once dry, the surface is smoothed with 180-220 grit sandpaper
- The surface is checked before painting; although the product has a factory primer, applying an additional primer is optional
- Finish with two coats of suitable paint
- For exterior applications, use UV-resistant paint and exterior-grade filler
- Clean the P5040D Pilaster Capital with a soft, slightly damp cloth that will not damage the surface
- Do not use stiff brushes, abrasive powders, solvent-based products or chemicals that could scratch the surface
- Check the joints and painted surface during cleaning
- For exterior applications, regularly inspect the condition of the UV-resistant paint film, joint filler and screw points
- If cracks, blistering paint or exposed fixings are found, clean and repair the affected area, then renew it with a suitable paint system
Can the P5040D Pilaster Capital be used outdoors?
Yes, the P5040D can be used outdoors at the upper section of decorative pilaster and column compositions. The product does not carry structural loads; it is applied as a decorative element over an existing facade or supporting system. Since unpainted polyurethane may yellow under UV exposure, a UV-resistant exterior paint must be used. Joints and screw points should be sealed with exterior-grade filler, and the paint and joints should be inspected according to exposure conditions.
How is the P5040D installed and painted?
After the surface has been cleaned and dried, measure the piece and prepare the required cuts with a 45° mitre. Use polyurethane (PU) mounting adhesive for installation; silicone is not recommended. Mechanical fixing with screws is mandatory. Fill the joints and screw points, then smooth them with 180-220 grit sandpaper. The factory primer prepares the surface for painting, while an additional primer is optional. Apply two coats of suitable paint.
What are the weight and service life of the P5040D?
The product card does not specify the net weight of the P5040D, so providing an estimated kilogram value would not be accurate. Its rigid, closed-cell polyurethane structure provides water absorption below 1%, high dimensional stability and dimensional stability tested between -20 °C and +70 °C. Service life depends on installation quality, the paint system, UV exposure and maintenance conditions. The product is decorative and must not be used as a structural load-bearing element.
Why choose the P5040D instead of plaster or wood?
Rigid polyurethane is a lighter decorative material than plaster and offers greater resistance to impact. Compared with wood, it is more resistant to moisture and decay, while providing a harder, more detailed surface than EPS foam. Its closed-cell structure results in water absorption below 1%. It can also be cut, filled, sanded and painted. These advantages simplify installation and surface renewal in pilaster and column compositions.
What scale of pilaster design is the P5040D suitable for?
The P5040D's 56 x 56 cm square plan and 26 cm depth are suitable for wide pilaster arrangements rather than narrow decorative trims. It creates a balanced appearance at villa entrances, hotel lobbies, restaurant reception areas, living rooms and spacious entrance halls. It can be used to create a capital effect at the upper section. Final compatibility should be assessed together with the width of the pilaster shaft, the facade proportions and the surrounding architectural elements.